If your RC car goes backwards instead of forwards, there are a few things you can check. First, make sure that the battery is installed correctly and that the wires are connected properly. Next, check the transmission to see if it is in the correct position.
Finally, check the motor to see if it is running in the correct direction. If all of these things are working correctly and your car still goes backwards instead of forwards, then there may be an issue with the drivetrain or differential.
If you’ve ever had the misfortune of driving an RC car that goes backwards instead of forwards, you know how frustrating it can be. Here’s a quick fix that will help get your car back on track.
First, check to see if the batteries are properly installed.
If they are, then the problem may be with the motor itself. Try flipping the motor around and see if that makes a difference.
If neither of these solutions work, then there may be something wrong with the transmission.
You can try adjusting the gears to see if that helps. If all else fails, you may need to replace the transmission entirely.
RC Car Throttle Backwards
RC Car Throttle Backwards: Why It Happens & How To Fix It If your RC car is going backwards when you throttle it, don’t worry – you’re not alone. This is a common issue that can be caused by a few different things.
Let’s take a look at why this happens and how to fix it. One of the most common causes of an RC car going backwards when throttled is incorrect battery installation. If your batteries are installed upside down, they will reverse the polarity and cause your car to go in reverse.
The fix for this is simple – just make sure that your batteries are installed correctly. Another common cause of this issue is loose wiring. If any of the wires connecting your battery to your motor are loose, they can create a short circuit that will cause your car to go in reverse.
The fix for this is also relatively simple – just check all of the connections and make sure they are tight. If neither of these solutions fixes the problem, it’s likely that there is something wrong with your motor or ESC (electronic speed control). This is typically more serious and will require you to contact a qualified technician for diagnosis and repair.
Traxxas Reverse Throttle
When you’re driving your Traxxas RC car, there may be times when you need to quickly reverse the direction of travel. To do this, simply press and hold the reverse throttle trigger located on the left side of the controller. Doing so will cause your car to back up at a speed that’s proportionate to how far down you depress the trigger.
So, if you want your car to back up slowly, barely depress the trigger; whereas, if you want it to back up quickly, press the trigger all the way down. Releasing the reverse throttle trigger will cause your car to stop backing up and return to moving forward under regular throttle control.
Traxxas Only Goes in Reverse
If you’re a fan of RC cars, then you know that Traxxas is one of the leading brands in the industry. They make high-quality products that are loved by many. However, there is one downside to Traxxas cars – they can only go in reverse!
This may not seem like a big deal at first, but it can be quite frustrating if you’re trying to race your friends or compete in an event. It’s also worth noting that this isn’t a feature of all RC cars, so if you’re looking for a car that can go both forward and backward, then Traxxas isn’t the brand for you.
Despite this setback, Traxxas still makes great products and their cars are enjoyed by many people around the world.
If you can get past the fact that they can only go in reverse, then you’ll likely find yourself having a lot of fun with a Traxxas car!
Traxxas Slash Reverse Problem
One of the most common issues that arise with the Traxxas Slash is its reverse problem. In short, the issue occurs when users try to put their truck into reverse and it doesn’t work. This can be extremely frustrating, especially if you’re in the middle of a race or trying to park your truck.
There are a few things that can cause this issue, so let’s take a look at each one.
The first thing to check is your battery. If your battery is low on power, it may not have enough juice to engage thereverse function.
Make sure you charge your battery fully before attempting to use reverse again.
Another potential cause could be dirty or damaged gears. If your gears are gummed up with dirt and debris, they may not be able to engage properly.
Inspect your gears and clean them off if necessary. You may also want to consider replacing them if they appear damaged beyond repair.
Lastly, there could be an issue with your electronic speed control (ESC).
If your ESC is set too low, it may not provide enough power to engage reverse. Try adjusting your ESC settings and see if that solves the problem.
If you’re still having trouble getting reverse to work on your Traxxas Slash, contact customer support for further assistance.
Traxxas TQ 2.4 Throttle Reverse
When it comes to RC cars, one name that always comes up is Traxxas. The company has been around since 1986 and has gained a reputation for making high-quality products. One of their most popular products is the TQ 2.4 throttle reverse.
This RC car is known for its speed, durability, and overall performance. The TQ 2.4 throttle reverse is an electric car that can reach speeds of up to 30 mph. It comes with a 7-cell NiMH battery pack and a charger, so you can get started right away.
The car also features a waterproof design, so you don’t have to worry about it getting damaged in the rain or snow. One of the best things about the TQ 2.4 throttle reverse is its price. It’s very affordable for an RC car of this quality, making it a great option for those on a budget.
If you’re looking for an RC car that’s fast, durable, and won’t break the bank, the TQ 2.4 throttle reverse from Traxxas is a great choice!
Traxxas TQI Throttle Calibration
If your Traxxas model is equipped with the TQi radio system, you can calibrate the throttle by following these Steps:
1. Power on your transmitter and then power on your vehicle.
2. Press and hold the SET button on the transmitter.
3. While holding SET, fully depress and release the throttle trigger. The LED on the transmitter will begin flashing to indicate that calibration mode has been entered.
4. Slowly depress and release the throttle trigger several times, making sure that the trigger is released completely each time.
The LED will flash faster as you approach full throttle, and slower as you release the trigger back to idle position.
Traxxas TQ Reverse Steering
When you’re driving your Traxxas vehicle in reverse, the last thing you want is for it to keep going straight! That’s where reverse steering comes in. This handy little feature allows you to make your car turn while in reverse, making it much easier to navigate tight spots and get out of tough situations.
To use reverse steering, simply press and hold the button on your transmitter marked “Reverse Steering.” This will engage the feature and allow you to steer your vehicle left or right while in reverse. When you’re finished using reverse steering, simply release the button and your car will drive straight again.
If you’re looking for an easy way to make backing up a breeze, look no further than Traxxas TQ Reverse Steering!
Traxxas VXL-6S ESC Programming
As anyone who’s into RC cars knows, the Traxxas VXL-6S is one of the best ESCs on the market. It’s packed with features and is very user-friendly. However, there are a few things that you can do to make it even better.
One of those things is programming it for your specific needs. In this blog post, we’re going to go over how to program your Traxxas VXL-6S ESC. We’ll cover everything from what software you need to what settings you should use.
By the end of this post, you’ll be an expert at programming your ESC! First, let’s talk about what software you need. The Traxxas VXL-6S comes with its own software that’s designed for Windows computers.
If you don’t have a Windows computer, don’t worry – there’s also a Mac version available for download on the Traxxas website. Once you have the software installed on your computer, open it up and plug in your ESC via the USB cable. You should see a screen that looks something like this:
Now it’s time to start configuring your ESC! The first thing you’ll want to do is set the motor type. For most applications, brushed motors will work just fine.
However, if you’re using a brushless motor, you’ll want to select that option from the drop-down menu. Next, set the cutoff voltage. This is important because it determines how much power your motor will receive before it cuts off.
If you set the cutoff voltage too low, your motor may not have enough power to run properly; if you set it too high, your battery may drain too quickly. A good rule of thumb is to start at 3V and adjust from there based on how your car performs. The next setting is max throttle . This one is pretty self-explanatory – it sets the maximum throttle position that your car can reach. If you’re not sure what value to use here, start at 100% and adjust as needed based on how fast you want your car to go. Just remember: safety first! Don’t push your car beyond its limits just because you can; always be aware of what obstacles are around you and drive accordingly . After max throttle , we have brake strength .
Why Does My RC Car Not Go Forward?
If your RC car is not going forward, there are a few potential reasons why. The most common reason is that the batteries may be low and need to be replaced. Another possibility is that the gears may be stripped or damaged, which would need to be repaired or replaced.
Additionally, if the drive belt is loose or broken, this also needs to be fixed in order for the car to move forward again. Finally, check to make sure that all of the wheels are properly attached and inflated – if even one wheel is not securely attached or has low air pressure, it can cause the car to stall or not move correctly.
How Do You Reverse the Throttle Servo on a Traxxas TQ?
If you need to reverse the throttle servo on your Traxxas TQ, there are a few things you’ll need to do. First, locate the throttle servo reversing switch on the back of the transmitter. This switch is usually located near the battery compartment.
Once you’ve found it, move the switch to the “REV” position.
Next, go to your model’s menu and scroll down to the “Throttle Servo Reversing” option. Select this option and then choose “Yes” to confirm that you want to reverse the throttle servo.
That’s all there is to it! Once you’ve reversed the throttle servo, your model will be able to run in both forward and reverse directions.
Why Won T My Traxxas Slash Go in Reverse?
If you’re having trouble getting your Traxxas Slash to go in reverse, there are a few things you can check. First, make sure that the battery is fully charged. If the battery isn’t charged, the car may not have enough power to move in reverse.
Next, check the transmission. The transmission may be set to neutral instead of reverse. To change this, simply move the shift lever on the transmission to the reverse position.
If neither of these solutions work, there may be an issue with the motor or ESC (electronic speed control). Try checking the connections between these components to make sure they’re secure. Finally, if all else fails, consult your local hobby shop or Traxxas dealer for assistance.
TRCC TECH TIP – How to fix your brushless RC if its going faster in reverse than it is forward
Conclusion
The remote-control (RC) car goes backwards instead of forwards because the battery is installed incorrectly. The positive and negative terminals on the battery must be facing the correct direction in order for the RC car to go forwards. If the battery is installed backwards, then the RC car will go backwards instead of forwards.